We updated our Privacy Policy and Terms on October 22, 2026.

Skip to main content
Fertilizing Print / Save PDF
BLADEBOSS
FLIGHT MANUAL · HOW-TO SERIES
GUIDE FERT-03 · REV D
Flight School for Your Lawn

How to Winterize Your Lawn (Winterizer and Final Mow)

Winterizing is the last job of the season and the one that sets up next spring: a small late-fall feeding with potassium, a staged final mow, a clean lawn and drained sprinklers. The grass decides when the feeding works best. Your county may decide when it has to be done. Here is how to get both right.

Updated Oct 2026
Difficulty
★★★★★
Active Time
1-2 Hours
Best Season
Late Fall (Before Your County's Deadline)
Cost
$40-$70

Pre-Flight Checklist - What You Need

FALL WINTERIZER
Scotts Turf Builder WinterGuard (32-0-10)
Scotts Turf Builder WinterGuard (32-0-10)
$69.99
VIEW ON AMAZON →

As an Amazon Associate, Blade Boss earns from qualifying purchases. It never costs you a penny more.

Mission BriefingWinterizing is the year's last feeding plus the jobs that put the lawn to bed: clear the leaves, spread about 0.50 lb of actual nitrogen per 1,000 sq ft, with potassium, stage the final mow down, then blow out the sprinklers. Agronomically, it goes down after your last mow, while the grass is still green, which on Long Island is usually mid to late November. Legally, your county or state may stop you sooner. On Long Island, where Blade Boss started, finish by October 31st in Suffolk County, before November 15th in Nassau County, and before December 1st anywhere else in New York State.
Pro TipThe dates above are the county's. Your soil is your own. See it. Read my lawn

Rules of Engagement (ROE's)

Always
Time it by the grass, not the calendar: after your last mow, while the grass is still green.
Know your county's deadline and finish by the last legal day. If it comes before your last mow, apply in the week before it.
Feed about 0.50 lb of actual N per 1,000 sq ft, with potassium along for cold hardiness.
Clear every leaf before you apply, so the feed reaches the soil.
Lower the mowing height gradually over 2 to 3 cuts to the final height.
Blow out the sprinklers after the winterizer is watered in.
Never
Apply weeks early just to be done. Early nitrogen goes into tender top growth that winter kills.
Apply after the ground freezes. The nutrients sit on top and wash away, wasted.
Push much past 0.50 lb of N. Excess late nitrogen feeds snow mold and leaches on sandy soil.
Apply any fertilizer after your county's deadline. In Suffolk, in Nassau and under New York State law that includes potash-only products; plain agricultural lime is exempt.
Scalp the final cut in one pass. Dropping straight to the low height shocks and exposes the crowns.
Leave a layer of leaves under the snow. Matted leaves plus snow is a fungal guarantee.
Skip the irrigation blow-out. One frozen pipe is a several-hundred-dollar repair.
Fertilizer deadlines on Long Island, where Blade Boss started. All three count potash-only products as fertilizer, and plain agricultural lime is exempt from all three. Elsewhere, check your own county and state: most places have no fall blackout, and the ones that do set their own dates.
WhereThe lawNo fertilizerLast legal dayPenalty
Suffolk CountySuffolk County Code §459-9BNovember 1st to April 1stOctober 31stUp to $1,000 per violation, each day a separate violation
Nassau CountyNassau County Local Law 11-2009November 15th to April 1stNovember 14thUp to $250, then $500, then $1,000
Rest of New York StateNY Environmental Conservation Law, Article 17, Title 21December 1st to April 1stNovember 30thHouseholds: a written warning, then up to $100, then up to $250

The Flight Plan - Step by Step

Time It by the Grass, Not the Calendar

The classic timing is after your last mow, while the grass is still green. Top growth has stopped but the roots are still working, so the grass stores the nitrogen instead of spending it on a flush of tender leaves. If you want a number, the soil should still be above about 40 degrees.

On Long Island the grass would still use a winterizer from about November 10th to 25th, as growth slows and then stops. Suffolk County's deadline comes before that window opens and Nassau County's lands in the middle of it, which is why the next step matters.

Pro TipWhen the law comes first: if your county's deadline arrives before your last mow (Suffolk's does), apply in the last week before the deadline at the normal rate. The grass would still use it later, but the law ends fertilizer on that date, and the latest legal day is the closest you can get.

Find Your County's Fertilizer Deadline

Before you pick a date, check whether your county or state bans fertilizer in late fall. Most places don't, but where a blackout exists, the date is the law, and it can fall weeks before the grass stops growing. On Long Island there are three, and the strictest one that covers your address is the one that counts (see the table above).

Hold ShortWARNING: In Suffolk County it is against the law (County Code §459-9B) to put any fertilizer on turf from November 1st to April 1st, potash-only products included. Nassau County's Local Law 11-2009 bans fertilizer on turf from November 15th to April 1st, potash-only products included. New York State law bans fertilizer on every lawn from December 1st to April 1st, potash-only products included. Plain agricultural lime is exempt under all three. In 1978 the EPA designated the aquifer under Nassau and Suffolk a sole-source aquifer, the counties' principal source of drinking water.

Two more rules apply all season. New York State law keeps fertilizer 20 feet from surface water unless a continuous natural vegetative buffer at least 10 feet wide separates the lawn from the water; with a spreader guard, deflector shield or drop spreader, the state limit is 3 feet. In Suffolk County the county rule is stricter: 20 feet unless that 10-foot buffer is there (County Code §459-9C), with no spreader exception. And New York allows phosphorus only if a soil test shows your lawn needs it or the lawn is new in its first season, so pick a winterizer with a zero in the middle unless your test says otherwise.

Clear Every Last Leaf First

Before any product goes down, the lawn has to be clean. A winterizer application can only work if it actually reaches the soil, and a blanket of leaves blocks it. Worse, leaves left to mat down under snow trap moisture against the turf all winter and create a perfect nursery for snow mold.

Clear it all: rake or blow out every leaf, twig, and pile of debris, right down to clean turf. Do not talk yourself into leaving a thin layer as natural mulch on the lawn itself. On beds, sure, but on the grass a matted leaf layer plus snow is a fungal party you will pay for in spring.

A person using a leaf blower to clear the last fallen leaves off a green lawn in late autumn, revealing clean turf behind
Clear every leaf down to clean turf. Matted leaves under snow trap moisture and grow snow mold.

Apply the Winterizer (0.50 lb N Plus Potassium)

The winterizer is a small nitrogen feeding with potassium riding along. The roots take up the nitrogen and store it as carbohydrate in the crowns and roots, and that stored energy powers the first growth in spring. Potassium helps the plant harden off for winter. Blade Boss's program puts the winterizer at about 0.50 lb of actual nitrogen per 1,000 sq ft, smaller than the September feeding.

  • Pick the right nitrogen. For your last feeding of the year, pick a fertilizer whose nitrogen still works in cool soil: fast-acting urea blended with sulfur-coated urea or IBDU. Skip organic and polymer-coated products for this one feeding. On Long Island's sandy soils, keep at least half of the nitrogen slow-release, and no more than 0.6 lb per 1,000 sq ft. That's Long Island's state and county recommendation, not a law.
  • Do the math for your bag. Divide 0.50 by the bag's first number as a decimal to get pounds of product per 1,000 sq ft: about 1.56 lb of a 32-0-10 or 2.08 lb of a 24-0-11. NitroCalc Pro does it for your exact square footage.
  • Calibrate the spreader for this product. Winterizer granules aren't sized like your spring fertilizer, so last spring's setting won't match. Here's how to calibrate.
  • Spread in two passes at half rate each, the second at a right angle to the first, on dry grass.
  • Keep it off hard surfaces, sweep any granules off the driveway and walks back onto the grass so they do not wash into storm drains.
  • Water it in if no rain is coming: about a quarter inch, half an inch at most.
Hold ShortHold Short: do not treat this like a summer feeding. Piling on nitrogen for one last green-up backfires two ways: it forces tender new growth that winter kills, and the lush tissue is exactly what snow mold feeds on under the snow. Stay at about 0.50 lb of N and let NitroCalc Pro set your exact numbers.

High-potassium "winter" products (a 10-0-20, for example) and potash-only products are still fertilizer under Suffolk's, Nassau's and New York State's laws, so they follow the same deadlines. For how quick-release and slow-release nitrogen differ, see our Lesco vs Scotts comparison.

Stage the Final Mow (Never Scalp It)

The last mow of the year comes in a little lower than your normal height, because tall grass matted under snow is a snow mold haven, but you get there gradually, never in one scalping pass. Dropping straight from your summer height to the low final height in a single cut shocks the plant and exposes the crowns right before the hardest season.

Step it down over your last two or three mows, taking no more than a third each time (the same one-third rule from every other mow), until you land at the final height. Bag these last cuts rather than mulching, since you want the surface clean and clear going into winter, not covered in clippings that mat down.

Where your county allows feeding after the last mow, finish the final mow first, then spread the winterizer. On Long Island the deadline usually comes first, so the winterizer goes down before your last few mows.

Diagram showing the final mow height stepped down gradually over three cuts from summer height to the lower winter height, versus a single scalping cut that shocks the lawn
Step the height down over the last two or three mows, a third at a time. Never scalp straight to the final height in one pass.

Blow Out the Sprinklers and Put It to Bed

The last job protects your plumbing, and the order matters: blow out the irrigation only after the winterizer is applied and watered in. You need that final drink to move the feed to the roots, and then you shut the water system down for good.

Blow out the sprinkler lines with compressed air, drain and disconnect hoses, and pull any timers or backflow devices that the manufacturer says to bring inside. One line left full of water and one hard freeze is a cracked pipe and a several-hundred-dollar spring repair. With the lawn fed, mown, cleared, and the water shut down, it is officially put to bed.

That's the last fall job. For everything that comes before it, from September seeding to October weeds, work through the fall lawn care checklist.

A garden hose drained, coiled, and disconnected from an outdoor spigot beside a dormant late-fall lawn
Blow out the lines after the winterizer is watered in. One frozen pipe is a several-hundred-dollar spring repair.

Get Your Exact Winterizer Rate in NitroCalc Pro

Winterizing is the one feeding where the numbers really matter, because a little too much nitrogen is the difference between a lawn that stores energy and one that grows snow mold. Enter your square footage and your winterizer's analysis, and NitroCalc Pro tells you exactly how much product to spread to land at about 0.50 lb of actual nitrogen per 1,000 square feet.

Open NitroCalc Pro →
Where are you in the fall window?
IF Grass is still growing fast and your deadline is weeks away
Too early. Nitrogen now goes into tender top growth. Wait for your last mow or the last week before your county's deadline, whichever comes first.
IF You've made your last mow, the grass is still green, and you're before your deadline
This is the window. Clear the leaves, spread about 0.50 lb of N and water it in. Set your exact rate in NitroCalc Pro →
IF Your deadline is days away and the grass is still growing
Apply before the deadline at the normal rate. It's the latest legal day and the closest you can get to the ideal timing.
IF Your county's deadline has passed but the grass is still green
Agronomically the grass could still use it. Legally, fertilizer is against the law where you live until April 1st (see the deadlines above). Put the money toward next September's feeding, which matters more anyway.
IF The ground is already frozen or snow has fallen
You missed it for this year. The nutrients can't get into frozen soil; they sit on the surface and wash away. Save the money, do a final cleanup mow if you can, and put winterizing at the front of next fall's plan.
IF You skipped the September feeding
September matters more than the winterizer for overall lawn health, and the winterizer can't fully make up for it. Apply the winterizer at the normal 0.50 lb rate (don't double it) and put September at the top of next year's plan.

The Winterizing Reference

Members get the winterizer timing reference, the nitrogen and potassium targets, and the full put-it-to-bed checklist so nothing gets missed before the freeze.

Free account. One field. No card.

Abort Criteria - Common Mistakes

Timing it by the calendar instead of the grass. Watch the lawn, not the date. Apply after your last mow, while the grass is still green, as long as your county's deadline hasn't passed.
Applying weeks early just to be done. Early nitrogen goes into a flush of tender growth that winter kills. If your county's deadline forces an early date, use the week before it, not a month before it.
Applying after the ground freezes. The nutrients cannot get into frozen soil, so they sit on top and wash away. If you miss the window, save the money for next fall.
Loading on nitrogen for one last green-up. Stay at about 0.50 lb of actual N per 1,000 sq ft. Excess late nitrogen feeds snow mold, forces winter-killed growth and leaches on sandy soil.
Feeding after your county's deadline because the weather is still warm. Warm weather doesn't move the date. On Long Island it's against the law from November 1st in Suffolk County and November 15th in Nassau County, and from December 1st everywhere in New York State. Potash-only products count under all three. Plan the week before.
Scalping the final mow in one pass. Dropping straight to the low final height shocks the grass and exposes the crowns. Step it down over two or three cuts, a third at a time.
Leaving a thin layer of leaves on the lawn. Leaves plus snow trap moisture and grow snow mold. Clear every leaf off the turf before winter, no exceptions on the grass.
Forgetting to blow out the irrigation. One line of water and one hard freeze cracks a pipe. Blow out the sprinklers after the winterizer is watered in, and drain the hoses.

Mission Complete. Now Fly the Plan.

Your soil isn't the county's. Type your address. We read your soil from the USDA survey and show you what to fix first. Read my lawn

Open NitroCalc Pro →▶ VIDEO WALKTHROUGH - COMING SOON

Crew Questions - FAQ

When should I apply winterizer to my lawn?

Apply it after your last mow, while the grass is still green; on Long Island the grass would still use it from about November 10th to 25th. Legally, check your county and state, because some ban fertilizer in late fall. On Long Island the law comes first: finish by October 31st in Suffolk County (County Code §459-9B), before November 15th in Nassau County (Local Law 11-2009), and before December 1st anywhere in New York State. When your deadline comes before your last mow, apply in the week before it.

How much winterizer should I put down?

About 0.50 lb of actual nitrogen per 1,000 sq ft, which is smaller than the September feeding. To convert that to product, divide 0.50 by the nitrogen percentage on the bag: about 1.56 lb per 1,000 sq ft of a 32-0-10 or 2.08 lb of a 24-0-11. More late-season nitrogen feeds snow mold and, on sandy soil, leaches.

What is the best winterizer fertilizer?

One that lands you at about 0.50 lb of nitrogen per 1,000 sq ft and carries some potassium for winter hardiness, with no phosphorus unless a soil test shows you need it (in New York, that's the law for an established lawn). Run the numbers for your bag rather than following a generic rate. High-potassium and potash-only products are still fertilizer under Suffolk's, Nassau's and New York State's laws, so they follow the same deadlines.

How short should I cut my grass for winter?

The final cut comes in a bit lower than your normal mowing height, because tall grass matted under snow invites snow mold, but you get there gradually. Step the height down over your last two or three mows, removing no more than one-third of the blade each time, rather than scalping straight to the low height in one pass. A single scalping cut shocks the grass and exposes the crowns right before the hardest part of the year.

Do I need to fertilize my lawn in the fall?

Yes. For cool-season grass, fall is the most important feeding season, but the September feeding matters more than the winterizer. September fuels root growth and recovery from summer; the winterizer tops off the plant's stored energy for spring. If you can only do one, do September. Done right, the winterizer is a small, cheap feeding; done wrong (too much nitrogen, too late) it does more harm than good.

Should I water in winterizer?

Yes. If rain is not in the forecast within a day or so, water the winterizer in with about a quarter inch, half an inch at most, to move the nutrients off the blades and into the root zone. Then, and only then, blow out and shut down your irrigation for the season. That order matters: you want the final watering to carry the feed to the roots before the water system goes offline.

Why do I need to blow out my sprinklers?

Any water left sitting in irrigation lines or a hose will expand when it freezes and can crack the pipe, the valves, or the backflow device, which turns into a several-hundred-dollar repair and a dead zone in spring. After the winterizer is applied and watered in, blow out the sprinkler lines with compressed air, drain and disconnect all hoses, and bring timers and backflow devices inside if the manufacturer recommends it. It is the last step of putting the lawn to bed.

Can I use a potassium-only winterizer after the blackout starts?

Not in New York. Suffolk County's law, Nassau County's law and New York State's law all count potash-only products as fertilizer, so they fall under the same dates: November 1st in Suffolk, November 15th in Nassau and December 1st statewide, all running to April 1st. Plain agricultural lime is exempt. Other states write their own rules (New Jersey's blackout covers only nitrogen and phosphorus fertilizer, for example), so check your own state and county.

When does grass stop growing on Long Island?

On Long Island, lawn growth slows in early November, once daily temperatures stay below about 50°F, and top growth effectively stops by late November. Keep mowing until it does; the last cut usually falls between mid- and late November.

What if I missed the winterizer window?

Your lawn will still survive the winter. If your county's deadline has passed, the law says wait until April 1st, so put the money toward next September's feeding, which matters more anyway. If the ground has frozen, the nutrients can't get in, so skip it either way.

All Guides
SCAN MY LAWN SCAN